too many to choose from here, stop posting all the pictures guys
| BBNovaRacing.com http://bbnovaracing.com/forum/ |
|
| window net mounting pictures http://bbnovaracing.com/forum/viewtopic.php?f=3&t=5508 |
Page 1 of 2 |
| Author: | jacobgiles [ Dec Thu 07, 2006 9:49 pm ] |
| Post subject: | window net mounting pictures |
i need a few pics of window nets. i need to look at different ways to mount them. preferably the upper area above the window. thanks |
|
| Author: | jacobgiles [ Dec Tue 12, 2006 9:04 am ] |
| Post subject: | |
too many to choose from here, stop posting all the pictures guys
|
|
| Author: | RICK MILLER [ Dec Tue 12, 2006 9:20 am ] |
| Post subject: | |
We just use a seatbelt buckle. Weld the male part to the bar ( be careful to put it in a position so that you don't cut your head open getting in and out) . Weld the female end to a rod that runs through the net. Simple and user friendly. 
|
|
| Author: | jacobgiles [ Dec Tue 12, 2006 9:29 am ] |
| Post subject: | |
on the upper rod, on the opposite end of the buckle, how do you attach that end of the rod? does it come out or pivot ? |
|
| Author: | jacobgiles [ Dec Tue 12, 2006 9:56 am ] |
| Post subject: | |
i was thinking something like this. 
|
|
| Author: | bbnova [ Dec Tue 12, 2006 9:56 am ] |
| Post subject: | |
Mine pivots.... |
|
| Author: | bbnova [ Dec Tue 12, 2006 9:58 am ] |
| Post subject: | |
Were you just thinking of inserting the rod into the hole in the plate??? Good thing Dogg isn't here to take this thread to a bad place..... |
|
| Author: | jacobgiles [ Dec Tue 12, 2006 10:18 am ] |
| Post subject: | |
kevin, the top has one buckle end and one pivot end? the bottom stays attached at both points, correct? |
|
| Author: | bbnova [ Dec Tue 12, 2006 10:59 am ] |
| Post subject: | |
I have a clevis at the top rear to pivot that says attached and a pin and clevis that secures the top front. Both bottom attachmetns stay attached. The front of the top bar will rotate down and rearward out of the way... |
|
| Author: | jacobgiles [ Dec Tue 12, 2006 11:06 am ] |
| Post subject: | |
thanks 
|
|
| Author: | bbnova [ Dec Tue 12, 2006 11:16 am ] |
| Post subject: | |
|
|
| Author: | Maliboost [ Dec Tue 12, 2006 12:45 pm ] |
| Post subject: | |
that pivot is a great idea. My buddies car has a hole that the rod slides into & then it snaps in with the buckle. It works great, but........ he cant do it by himself while he is buckled in. it takes a LONG time for him to get it done by himself. Bob |
|
| Author: | jacobgiles [ Dec Tue 12, 2006 12:49 pm ] |
| Post subject: | |
does he wear arm restraints or somthing? |
|
| Author: | bbnova [ Dec Tue 12, 2006 1:17 pm ] |
| Post subject: | |
It is real nice knowing it is where it is supposed to be when I grab for it.... |
|
| Author: | Maliboost [ Dec Tue 12, 2006 1:19 pm ] |
| Post subject: | |
No, its just where it sits with the way the roll bar crosses his shoulder & the seat that he has & the way that the floor board scoots it down under the seat that makes it a PITB. its REAL easy for me to get to it from outside the car, but when your in it & buckled in, its difficult. Bob |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|